Shaft extension 240 mm ø20 mm for damper shaft ø8...22.7 mm

End stop indicator, for NF..A / SF..A

Shaft clamp reversible, for central mounting, for damper shafts ø12.7 / 19.0 / 25.4 mm

Ball joint suitable for damper crank arm KH8, Multipack 10 pcs.

Actuator arm, for 3/4" shafts, clamping range Ø10...22 mm, Slot width 8.2 mm

Damper crank arm Slot width 8.2 mm, clamping range ø14...25 mm

Damper crank arm Slot width 8.2 mm, for Ø1.05"

Damper crank arm Slot width 8.2 mm, clamping range ø10...18 mm

Push rod for KG10A ball joint (36” L, 3/8” diameter).

Push rod for KG6 & KG8 ball joints (36” L, 5/16” diameter).

Wrench 0.32 in and 0.39 in [8 mm and 10 mm]

Retrofit clip, for NF..A / SF..A

Base plate extension, for NF..A / SF..A

Mounting bracket for AF..

Mounting bracket

Dual actuator mounting bracket.

Mounting bracket

Linkage kit

Mounting bracket
for AF / NF

Jackshaft mounting bracket.

Mounting kit for linkage operation for flat and side installation

Mounting kit, for foot mount installation

Damper clip for damper blade, 3.5” width.

Damper clip for damper blade, 6” width.

1" diameter jackshaft adaptor (11" L).

1-5/16" diameter jackshaft adaptor (12" L).

1.05" diameter jackshaft adaptor (12" L).

Resistor, to convert a 4...20 mA signal into a 2...10 V control signal

Resistor kit, 50% voltage divider

Transformer, AC 120 V to AC 24 V, 40 VA

Weather shield, 330x203x152 mm [13x8x6"] (LxBxH)

Base plate, for ZS-100

Weather shield, 406x213x102 mm [16x8-3/8x4"] (LxWxH)

Explosion proof housing, 406x254x164 mm [16x10x6.435"] (LxBxH), for NK.. / GM.. / GK.. / AM.. / LF.. / AF.. / NF.. / FS..F.. Series Actuators

Weather shield, 438x222x140 mm [17-1/4x8-3/4x5-1/2"] (LxBxH)

Weather shield, 438x222x140 mm [17-1/4x8-3/4x5-1/2"] (LxBxH)

Shaft extension, 1/2", for ZS-300

Shaft extension, 3/4", for ZS-300

Shaft extension, 1", for ZS-300

DC Voltage Input Rescaling Module

Convert Pulse Width Modulated Signal to a 2...10 V Signal for Belimo Proportional Actuators

Positioner for wall mounting

Positioner for front-panel mounting

Cable conduit connector, 1/2"

Signal simulator, designed to operate most modulating, floating point and on/off style actuators without the presence of a controller

Connection cable 16 ft [5 m], A: RJ11 6/4 ZTH EU, B: free wire end for connection to MP/PP terminal

Connection cable 10 ft [3 m], A: RJ11 6/4 ZTH EU, B: 3-pin Weidmüller and supply connection

Service Tool, with ZIP-USB function, for programmable and communicative Belimo actuators, VAV controller and HVAC performance devices

Gateway MP to BACnet MS/TP

Gateway MP to LonWorks

Gateway MP to Modbus RTU

Auxiliary switch, for 1/2" diameter shafts mount

Auxiliary switch, for 1" diameter shafts mount